收藏本站
SAW Components
SAW RF filter
B3907
447.70 MHz
Data sheet
ESD protection of SAW filters
SAW filters are E lectro S tatic D ischarge sensitive devices. To reduce the probability of damages
caused by ESD, special matching topologies have to be applied.
In general, “ESD matching” has to be ensured at that filter port, where electrostatic discharge is
expected.
Electrostatic discharges predominantly appear at the antenna input of RF receivers. Therefore
only the input matching of the SAW filter has to be designed to short circuit or to block the ESD
pulse.
Below three figures show recommended “ESD matching” topologies.
For wideband filters the high-pass ESD matching structure needs to be at least of 3 rd order to
ensure a proper matching for any impedance value of antenna and SAW filter input. The required
component values have to be determined from case to case.
Cs1
Cs3
Cs1
Cs3
Lp2
to output
matching
Lp2
to output
matching
Fig. 1 MLC varistor plus ESD matching
Fig. 2 Suppressor diode plus ESD matching
In cases where minor ESD occur, following simplified “ESD matching” topologies can be used
alternatively.
Cs1
Cs3
Lp2
to output
matching
Fig. 3 3 rd order high-pass structure for basic ESD protection
In all three figures the shunt inductor Lp2 could be replaced by a shorted microstrip with proper
length and width. If this configuration is possible depends on the operating frequency and
available pcb space.
Effectiveness of the applied ESD protection has to be checked according to relevant industry
standards or customer specific requirements
For further information, please refer to EPCOS Application report:
“ ESD protection for SAW filters ”.
This report can be found under www.epcos.com/rke.Click on “Applications Notes”.
Please read cautions and warnings and
important notes at the end of this document.
6
May 15, 2013
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
B39458M1971M100S1 FILTER SAW 45.75MHZ IF 5-SIP
B39458M3951M100S1 FILTER IF 45.75MHZ 5SIP VIDEO
B39811B4064U810 FILTER SAW 810MHZ LOWLOSS SMD
B39861B3563U410W9 FILTER SAW 864MHZ WIRELESS SMD
B39871B3715U410 FILTER SAW 869MHZ REMOTE SMD
B39871B3716U410 FILTER SAW 869MHZ REMOTE SMD
B39871B3717U410 FILTER SAW 866.5MHZ SMD
B39871B3725U410 FILTER SAW 869.0MHZ SMD
相关代理商/技术参数
B39451B4052U410 功能描述:信号调节 LOW LOSS 447.0 MHZ RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39451-B4052-U410 制造商:EPCOS 制造商全称:EPCOS 功能描述:SAW Components Low-Loss Filter for Mobile Communication 447,0 MHz
B39451B5028H810 功能描述:信号调节 IF 450.50MHz RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39451B5061U410 制造商:EPCOS 制造商全称:EPCOS 功能描述:Low-loss RF filter for CDMA base station
B39458G3653K100 功能描述:信号调节 PARALLEL 45.8 RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39458M1862M100 功能描述:信号调节 INTERCARRIER 45.8 RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39458M1864M100 功能描述:信号调节 INTERCARRIER 45.8 RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel
B39458M1865D100 功能描述:FILTER IF 45.75MHZ 5SIP RoHS:是 类别:滤波器 >> SAW 滤波器 系列:- 标准包装:1 系列:- 频率:433.92MHz 中心 带宽:600kHz 滤波器类型:带通 插入损耗:3.5dB 应用:远程控制 封装/外壳:TO-205AD，TO-39-3 金属罐 安装类型:通孔 包装:Digi-Reel® 高度（最大）:0.125"（3.18mm） 尺寸/尺寸:0.370" 直径（9.40mm） 其它名称:583-1172-6